ATCS Feeder

Free Windows software that decodes ATCS railroad data radio and feeds the packets to your aggregators.

More Packets From the Same Radio

We recorded the raw radio at a site monitoring CN's Stamford Sub and gave the same 110 minutes to both decoders: ATCS Monitor with FEC on, and ATCS Feeder.

Each block is 50 packets.

61% More Packets

1,947 against 1,206, every one passing its checksum.

Nothing Missed

Not one packet ATCS Monitor decoded was missed by ATCS Feeder.

Weak Locations Heard

Eight MCPs ATCS Monitor never decoded at all: ATCS Feeder delivered 81% of their messages.

Fewer Gaps

MCPs number their messages. Of those the numbers show were sent, ATCS Feeder decoded 84–92%, ATCS Monitor 51–58%.

How it was tested: 46 raw RTL-SDR recordings of the site's MCP side (2026-10-28), at two dongle gains. ATCS Feeder decoded the raw samples, using the release that went live there on 2026-11-03. ATCS Monitor's own decoder (atcsdata.dll 3.5.4, FEC on) decoded the FM audio of the same recordings. These figures are for one site; results elsewhere depend on the site's signals.

What's Different

ATCS Feeder doesn't replace ATCS Monitor's displays. It does one job, getting packets off the air and onto the network, and that's where the two differ.

ATCS FeederATCS Monitor
Receiver One RTL-SDR dongle covers all six channels of a side (BCP or MCP), or the ten A Block channels. A sound card works too. A radio or scanner feeding a sound card, one channel per receiver.
Decoding Decodes the radio samples directly (IQ), and falls back to an FM decoder for anything it misses. Decodes the receiver's FM audio.
Bad Packets Site rules hold back any packet the site's own traffic doesn't back up: an unknown sender, a broken sequence or an unseen payload. Designed for about one false packet a year. Checksum and FEC.
Feeding Built in. Up to three destinations at once, each with its own client ID, and each reconnects on its own. Packets wait up to two minutes through a dropout and are sent in order. Through its network server.
Unattended Runs without a window as a boot task. Restarts its decoder if it stalls, and waits for a dongle that's slow to appear after a power cut. A desktop program.

What It Decodes

Each protocol, by where the signal comes from.

RTL-SDRSound CardSD9 Radio
ATCS
ATCSThe 900 MHz BCP and MCP pairs and the A Block Yes, every channel of a side at once Yes No
ATCS-GenisysGenisys code-line data inside ATCS packets Yes Yes No
ARES
ARESVHF, such as 160.215 MHz Yes No No
ATCS over ARESATCS code-line messages carried on ARES Yes No No
Genisys
Genisys RFL300 baud on BCP or MCP tones Yes (experimental) Yes (experimental) No
Genisys 202TBell 202 tones at 1200 or 300 baud Yes (experimental) Yes (experimental) Yes, from SD9 radios on your network
Genisys 19200NThe SD9's own digital modem In development No Not tested

Experimental means tested on simulated signals, not yet proven at a live site. In development means decoding off the air at a test site, but not in a release yet.

What It Does

  • Names your MCPs and shows when each was last heard.
  • Logs every packet, sent or not, and keeps 14 days.
  • Records baseband audio for later replay, if you want it.

What It Doesn't

  • No track diagrams or control point displays. Keep ATCS Monitor for that.
  • No IEEE 802.16t, which at least one railroad runs in the A Block.
  • Windows only.

Download

ATCS Feeder is freeware. There's nothing to buy and no account to make.

Unzip all nine files into one folder and run ATCS.Feeder.exe. Each file ships with a SHA-256 checksum.

You'll Need

  • Windows 10 or 11, 64-bit.
  • The Microsoft Visual C++ 2015–2022 Redistributable (x64).
  • An RTL-SDR dongle with an R820T, R820T2 or R828D tuner (RTL-SDR Blog V3 or V4), or a radio and sound card.
  • A 900 MHz antenna that can hear your local MCPs.